Ice Bath Services
Explore our Morozko Service plans to discover the ideal option for your ice bath performance needs. Select your preferred frequency below, ranging from one-time, monthly, bi-monthly, and yearly cleaning services.
On-site Service by Morozko
One Time Service Cleaning
399$A technician will come out to drain the ice bath, clean the steel, change the filter, wipe down the filter housing, purge the plumbing lines, and give a full diagnostic of the ice bath.Valid for one month- Not Available Outside of the Continental U.S.
Monthly Service Cleaning
350$Every monthOnce a month, a technician will come out to drain the ice bath, clean the steel, change the filter, wipe down the filter housing, purge the plumbing lines, and give a full diagnostic of the ice bath.Valid for 12 months- Not Available Outside of the Continental U.S.
Bi-Monthly Service Cleaning
375$Every 2 monthsEvery other month, a technician will come to drain the ice bath, clean the steel, change the filter, wipe down the filter housing, purge the plumbing lines, and give a full diagnostic of the ice bath.- Not Available Outside of the Continental U.S.
- Best Value
One Year Service Cleaning
3,500$Once a month, a technician will come out to drain the ice bath, clean the steel, change the filter, wipe down the filter housing, purge the plumbing lines, and give a full diagnostic of the ice bath.Valid for 12 months- Not Available Outside of the Continental U.S.
Service Cleaning Checklist
The following steps outline the standard cleaning process for a Morozko ice bath, whether performed as part of a professional service visit or by the owner:
-
Drain and flush the ice bath to remove used water and buildup
-
Clean the stainless steel interior surfaces
-
Clean or replace the water filter as needed
-
Purge plumbing lines to maintain proper circulation
-
Inspect pump and filtration components for normal operation
-
Verify ozone disinfection is functioning properly
-
Refill, rebalance, and test the water before use
How-To-Videos
DIY Support
Adjust Water pH
Maintain water pH between 6.5–7.0 for optimal performance.
-
If pH is below 6.5, add ¼ cup magnesium carbonate directly to the water, allow circulation for one hour, then re-measure pH. Repeat as needed.
-
If pH is above 7.5, add one 2L bottle of seltzer water at a time, allow circulation, and re-measure until pH returns to range.
Add Epsom Salts
Epsom salts help improve ice quality and water performance.
-
Add 4–6 lb of pure magnesium sulfate (Epsom salt) evenly into the tub.
-
Keep the filtration system running and allow several hours for complete dissolution.
-
Use only pure salts without fragrances, oils, or additives.
Winter Operation (Outdoor Units)
Prevent freezing during cold weather operation.
-
When outdoor temperatures fall below 40°F (4°C), set the filtration timer to ON.
-
Run the filter pump continuously to keep water moving through the heated filter.
-
Set the ice bath temperature to 40°F as an added precaution.
Winter Shutdown
Safely shut down your ice bath for extended cold periods.
-
Unplug the unit and drain all water from the tub.
-
Remove the filter cartridge, rinse it, and allow it to dry completely.
-
Use towels or a shop vacuum to remove any remaining water from the filter housing.
-
Leave the filter housing slightly open to allow moisture to evaporate.
Basic Setup
Follow these steps when first setting up your ice bath.
-
Begin filling the tub and plug in the unit once water covers the plumbing ports.
-
Set the desired temperature and continue filling until the water level is about 6 inches below the rim.
-
Bleed air from the filter system, turn on the pump, and inspect for leaks.
Cold Exposure Safety
Practice safe cold exposure habits.
-
Exit the ice bath before shivering becomes prolonged.
-
Dry off immediately after exiting the tub.
-
Use light movement, such as walking or gentle exercises, to restore circulation.
